Ningbo Brando Hardware Co., Ltd
Focus on your demands Offer you best solution
Add to Cart
Airtac Type SC63x150 Air Cylinder Pneumatic Double Acting
Air cylinders, referred to as actuators, are devices that use compressed air as the source of gas and converts the pressure energy of the gas into mechanical energy with the form of rotary or linear motion. Different from hydraulic actuators, air cyclinders are very clean operating because the operating fluid is a gas, which prevents leakage from dripping and contaminating the environment.
Specifications of SC Series Pneumatic Cylinder:
| Bore Size (mm) | 32 | 40 | 50 | 63 | 80 | 100 | 125 | 160 | 200 | 250 | |
| Acting Type | Double Acting | ||||||||||
| Fluid | Air (to be filtered by 40μm filter element) | ||||||||||
| Mounting Type | SC | Basic FA FB CA CB LB TC TCM1 | |||||||||
| SCD, SCJ | Basic FA LB TC TCM1 | ||||||||||
| Operating Pressure Range | 0.15 to 1.0 MPa (1.5 to 10.0 bar) (22 to 145 psi) | ||||||||||
| Proof Pressure | 1.5 MPa (15 bar) (215 psi) | ||||||||||
| Temprature (℃) | -20 to +70 | ||||||||||
| Speed Range (mm/s) | 30 to 800 | 30 to 500 | |||||||||
| Cushion Type | Variable cushion | ||||||||||
| Adjustable Cushion Stroke (mm) | 21 | 28 | 29 | 36 | 40 | ||||||
| Port Size | 1/8'' | 1/4'' | 3/8'' | 1/2'' | |||||||
Stroke of SC Series Pneumatic Cylinder:
| Bore Size (mm) | Standard Stroke (mm) | Max. Standard Stroke | Max. Stroke |
| 32 | 25 50 75 80 100 125 150 160 175 200 250 300 350 400 450 500 | 1000 | 2000 |
| 40 | 25 50 75 80 100 125 150 160 175 200 250 300 350 400 450 500 600 700 800 900 1000 | 1200 | 2000 |
| 50 | 1200 | 2000 | |
| 63 | 1500 | 2000 | |
| 80 | 1500 | 2000 | |
| 100 | 1500 | 2000 | |
| 125 | 1200 | 2000 | |
| 160 | 1500 | 2000 | |
| 200 | 1500 | 2000 | |
| 250 | 1500 | 2000 |
Symbol of SC Series Pneumatic Cylinder:
Ordering Code of SC Series Pneumatic Cylinder:
Criteria for selection: Cylinder thrust:
Installation & Usage:
1. When load changes in the work, the cylinder with abundant output capacity shall be ed.
2. Relative cylinder with high temperature resistance or corrosion resistance shall be chosen under the condition of high temperature or corrosion.
3. Necessary protection measure shall be taken in the environment with higher humidity, much dust or water drops, oil dust and welding dregs.
4. Dirty substances in the pipe must be eliminated before cylinder is connected with pipeline to prevent the entrance of particles into the cylinder.
5. The medium used by cylinder shall be filtered to 40μm or below.
6. Anti-freezing measure shall be adopted under low temperature environment to prevent moisture freezing.
7. The cylinder shall be carried out test run without load before application. Prior to run, buffer shall be turned to the minimum and gradually released to avoid the damage on cylinder caused by excessive impact.
8. The cylinder shall avoid the influence of side load in operation to maintain the normal work of cylinder and extend the service life.
9. If the cylinder is dismantled and stored for a long time, please conduct anti-rust treatment to the surface. Anti-dust caps shall be added in air inlet and outlet ports.
Focus on your demands, Offer you best solution:
√ Contact us if some points you have doubt
√ Contact us if somewhere need to change
√ Contact us if not the one you are looking for
√ Contact us if you are doing designing
Welcome to your any question and inquiry!